Search results

This is a very popular one: https://a.co/d/jleFlDB Never noticed this short link on the picture.

One that showed up won't work to hold board against fence but with extended height fence would help hold the board down on machines surface. THIS is a spectacularly nice tool. Apparently the wheels have a sprag function so will only spin one direction. Works like a brake to help prevent...

Ordered this. Main purpose is to keep material snug against fence or end up with a crooked cut. https://www.amazon.com/dp/B09VB4L7H6?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1 Actually ordered another set by mistake. It's supposed to be here today. Didn't have option of return before delivery so...

Another flipped picture. Guess now that I look at it, could have cleaned off that table and used it. Just run out of room to maneuver with that tho. I think. Would be fine for the outfeed end tho.

Two stands for 10 bucks in Wilson. About hour drive for the whole trip. Perfect! Waiting on the magic fingers to be delivered plus have eye Doc appointment at noon. Gonna cut an old board as a test.

Picking up a roller stand dealio tomorrow in Wilson NC listed for 5 bucks. Says rusty. If it will telescope it'll work. If the roller works I'll do cartwheels.

I wasn't offended by ur comment. Just saying, whole lot of drivel here. Almost as bad as my shed thread. And NASCAR is DEFINITELY a monopolistic business. <on topic>

My post has no less relevance to the proceedings than anyone else's. Just trying to offer my contribution. Actully was looking for something in my computer and stumbled onto those pictures. It's kind of a funny story. Except the engine I put in was slap worn out. Whoops! They brought it with...

Old Ford 7.3 diesel engine harness. Customer said needed engine (rollback truck) and brought a used engine with the truck. I did as I was told and installed engine. No testing before hand as i suggested. The glow plugs get fed juice thru the valve cover gaskets and both side were torched. When I...

Slightly newer version of my saw. Need these casters! Then decide what height to build.

Just occurred to me, could just line them up, remove the wheels from the bench. Think be really close on height. Close enough to slip small piece of OSB under it to tune it.

In picture nearly 1/2" lower than bench. If anything rather have saw slightly proud. I'm only good for maybe 4 hours of doing stuff. Lower backs says no mas.

Two 2x4 stacked (1.5 + 1.5) with piece of 1/2" plywood over gets saw up to where the shed bench will work for in-feed. I'm more worried about that than the out- feed. Still might build a base structure/box for the porch. Really like to put it somewhere and leave it. The stand is 26x24. Wouldn't...

This is what I'm talking about. He's a bit of a show pony but that's what he's getting paid for. Be no sanding plywood in my shop! Manly cause I'm too lazy.

Was trying to figure out a way to use saw on the trailer. Need to rip edge of 12 foot 2x6. OK...you have infeed & outfeed. Table entry side (infeed) is little over 12 inches. Leaves 11 foot of board flopping in the wind with you 11 + feet from saw pushing the board hoping it doesn't kickback and...

I'll start posting every hour.

Still has the spotted pony look. I COULD paint some of it any time I get the urge. Just haven't had that urge yet. I'd like to replace the sides of the original shed before painting the rear. Takes five sheets of that pre-primed siding @175ish + tacks. Probably be spring for that part. Like to...

Left tail light works but signal doesn't. I'll find my crimp connectors and cut the turn signal wire and test as don't think can remove the lens? I'll start at front connector tho. It may be the adapter under the truck. Think it was new also but nothing is any good anymore. Nearly everything you...

We have a table saw. 100 bucks 7 minutes from home.