Storage building

Let's see if can attach. Nope. This video is too large...but the roof is off! Drug it off with long ratchet strap and my truck. We're nothing to it.
 

Attachments

  • IMG_20250423_104209646_HDR.jpg
    IMG_20250423_104209646_HDR.jpg
    2.5 MB · Views: 7
I'm done for today. Back has decreed that, if I continue any further today, it will kill me at 2:36 AM. No exceptions. Need to trim inch off top of original siding, on both sides, then ready to nail the top plate on. Probably fabricobble way to build a work surface like did on new section. Only issue is, the new section has holes in the sides cause NO SIDING. Made it easy to stuff 14 foot 2x8 thru, So will, using pieces of the rafters from old roof scabbed together, make a structure inside the structure of the structure I'm structuring into a larger structure. Put two layers of 1/2 OSB on it to stand on. Probably put legs under the legs holding the legs.

Then maybe get some truss set. None set today. Only issue is, somehow, one wall is 1/4ish" taller than other. Still thinking about that. Run some strings and see if can get it tuned in. Possibly use some strips of the old siding to make up the difference. I mean...the roof will hold it down, right?
 

Attachments

  • IMG_20250423_152909453.jpg
    IMG_20250423_152909453.jpg
    5.1 MB · Views: 6
  • IMG_20250423_152844941_HDR.jpg
    IMG_20250423_152844941_HDR.jpg
    4.4 MB · Views: 5
  • IMG_20250423_144917848.jpg
    IMG_20250423_144917848.jpg
    1.8 MB · Views: 5
  • IMG_20250423_144905176_HDR.jpg
    IMG_20250423_144905176_HDR.jpg
    2.5 MB · Views: 7
Third picture shows where I used 3/4 OSB in between the plates. Oddly enough, other side came out perfectly. This is why you don't start at the half-way mark. Should have removed old roof, then built and addition to FIT the existing structure. Only problem with that is would have been catching rain for months.

IF I could get the top plate off and replace that OSB with 2x4 probably be 1/4" high then. Anyone seen my stapler? I can't find my stapler...

1745439278718.png
 
Went back out and hung another concussion maker (2x8 for scaffolding) and trimmed the siding. Set plates up but didn't nail. Cleaned bunch of the 5 foot original rafters by pulling nails and removing the mending plates. Need to go up in the attic/loft and add some diagonals. With no siding or roof it has some wobble if you try to push it sideways. Shoved 4 or 5 old sheets of OSB up into loft. Likely add some cross pieces where they stay as I don't really trust that 3/4 inch the edge sets on.

I'm being really anal about that tho.
 
So...Hardee's Chicken biscuit & coffee: CHECK!

Came home and turned power on to shed/kick-started air compressor: CHECK!

Sitting in recliner with vibrating/heating pad behind back: CHECK!

Next will be...I'M SO TIRED! CHECK BOUNCED!
 
Have 12 foot 2x4's on top plate of 10 foot stricture. Standing under 2 foot sticking out, on a stool, marking where to cut them. 12ish inches is the thought. By time I spent less than 2 minutes finding the tools and getting it done...sick as a dog from looking up. Tried to fight thru it and managed to get a truss about 3/4 way in place. Have to climb up into the cathedral and hang the darned winch. Just can't make myself do it.

Realized have to buy more screws for the truss. Or not. Ones I had must be 7-8 inches long. Have enough to set 3 truss. I CAN do it another way, and probably will, by drilling angled holes and using 4" I have. They will all get toe-nailed after everything is set/measured & if Katy Perry makes it back from Mars.

Bleh. Ice cream. I think ice cream will make me feel better?
 
Only two to go and one is the gable end. Need to do a little work to gable. Have to cut thru siding for doors and install hinges. Trim lower part of siding an inch or so. Have to trim top of siding above front door and attach the flashing strip before setting gable. But we closing in on this biotch. Weather be coming.
 

Attachments

  • IMG_20250425_112420567_HDR.jpg
    IMG_20250425_112420567_HDR.jpg
    2.8 MB · Views: 3
  • IMG_20250425_110819342_HDR.jpg
    IMG_20250425_110819342_HDR.jpg
    2 MB · Views: 2
  • IMG_20250425_110224440_HDR.jpg
    IMG_20250425_110224440_HDR.jpg
    2.8 MB · Views: 2
One more too go. That last one was a pain in the patootie. Had it up and when running first screw in it fell over. Only one that did to me. After I washed my butt and changed clothes, tied it off 14 ways so couldn't move. It's up thar!😃 Now sitting in recliner with heating pad behind back and feet in the bubbly spa. Clothes in the washer. Been doing laundry every 4th day lately. Need to get couple pair pants hemmed so have 5-6 days worth.
 
We be jammin!💕😍💕 Probably end up going back out after clothes are done and do some cutting on gable end siding. Not looking forward to cobbling the lift for that. If had 14 foot step ladder be better except... don't think could get it in their and stood up. Did I mention I'm terrified?😉
 

Attachments

  • IMG_20250425_112420567_HDR.jpg
    IMG_20250425_112420567_HDR.jpg
    2.8 MB · Views: 5
  • IMG_20250425_134602560.jpg
    IMG_20250425_134602560.jpg
    4.4 MB · Views: 4
  • IMG_20250425_143515694_HDR.jpg
    IMG_20250425_143515694_HDR.jpg
    3.4 MB · Views: 4
  • IMG_20250425_145118715_HDR.jpg
    IMG_20250425_145118715_HDR.jpg
    4.3 MB · Views: 4
  • IMG_20250425_154838126_HDR.jpg
    IMG_20250425_154838126_HDR.jpg
    2.3 MB · Views: 4
  • IMG_20250425_154840566_HDR.jpg
    IMG_20250425_154840566_HDR.jpg
    3.1 MB · Views: 4
Realized the ridge block attached to last one is wrong. 2ish inches too long. Not sure exactly how I'll measure that one. Need gable up to measure. Need block in so it doesn't try to fold up like a cheap suit. Hmmm? Could add some wedges to one side so has 8 inch surface to sit on
 
You must log in or register to reply here.
Back
Top Bottom